NetBSD Problem Report #35320

From www@NetBSD.org  Mon Dec 25 23:14:33 2006
Return-Path: <www@NetBSD.org>
Received: by narn.NetBSD.org (Postfix, from userid 31301)
	id 22AA063B8C9; Mon, 25 Dec 2006 23:14:33 +0000 (UTC)
Message-Id: <20061225231433.22AA063B8C9@narn.NetBSD.org>
Date: Mon, 25 Dec 2006 23:14:33 +0000 (UTC)
From: eau@phear.org
Reply-To: eau@phear.org
To: gnats-bugs@NetBSD.org
Subject: ath(4) doesn't seems to work anymore
X-Send-Pr-Version: www-1.0

>Number:         35320
>Category:       kern
>Synopsis:       ath(4) doesn't seems to work anymore
>Confidential:   no
>Severity:       serious
>Priority:       high
>Responsible:    kern-bug-people
>State:          open
>Class:          sw-bug
>Submitter-Id:   net
>Arrival-Date:   Mon Dec 25 23:15:04 +0000 2006
>Originator:     Eric Auge
>Release:        -current
>Organization:
individual
>Environment:
NetBSD kamehouse.no.phear.org 4.99.5 NetBSD 4.99.5 (KameHouse) #1: Mon Dec  4 14:36:53 CET 2006  root@kamehouse.no.phear.org:/usr/obj/sys/arch/i386/compile/KAMEHOUSE.MPACPI i386

>Description:
my laptop is an x60 running -current, pluging an atheros pcmcia card into my laptop, the card was working fine in the previous release netbsd-3, now i get :

[...]
ath0 at cardbus0 function 0
ath0: unable to attach hardware; HAL status 13
[...]

here is my dmesg :
Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005, 2006
    The NetBSD Foundation, Inc.  All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
    The Regents of the University of California.  All rights reserved.

NetBSD 4.99.5 (KameHouse) #1: Mon Dec  4 14:36:53 CET 2006
        root@kamehouse.no.phear.org:/usr/obj/sys/arch/i386/compile/KAMEHOUSE.MPACPI
total memory = 1526 MB
avail memory = 1491 MB
timecounter: Timecounters tick every 10.000 msec
timecounter: Timecounter "i8254" frequency 1193182 Hz quality 100
BIOS32 rev. 0 found at 0xfd690
SMBIOS rev. 2.4 @ 0xe0010 (67 entries)
PCI BIOS rev. 2.1 found at 0xfd82b
pcibios: config mechanism [1][x], special cycles [x][x], last bus 24
PCI IRQ Routing Table rev. 1.0 found at 0xfdea0, size 272 bytes (15 entries)
PCI Interrupt Router at 000:31:0 (vendor 0x8086 product 0x122e compatible)
mainbus0 (root)
pci_addr_fixup: 000:31:2 0x8086 0x27c4 new address 0x00005800
pci_addr_fixup: 000:31:2 0x8086 0x27c4 new address 0x00005808
pci_addr_fixup: 000:31:2 0x8086 0x27c4 new address 0x00005810
pci_addr_fixup: 000:31:2 0x8086 0x27c4 new address 0x0000580c
cpu0 at mainbus0: apid 0 (boot processor)
cpu0: Intel Pentium M (Yonah) (686-class), 1828.85 MHz, id 0x6e8
cpu0: features bfe9fbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR>
cpu0: features bfe9fbff<PGE,MCA,CMOV,PAT,CFLUSH,DS,ACPI,MMX>
cpu0: features bfe9fbff<FXSR,SSE,SSE2,SS,HTT,TM,SBF>
cpu0: features2 c1a9<SSE3,MONITOR,VMX,EST,TM2,xTPR>
cpu0: "Genuine Intel(R) CPU           T2400  @ 1.83GHz"
cpu0: I-cache 32 KB 64B/line 8-way, D-cache 32 KB 64B/line 8-way
cpu0: L2 cache 2 MB 64B/line 8-way
cpu0: using thermal monitor 1
cpu0: Enhanced SpeedStep (1404 mV) 1833 MHz
cpu0: unknown Enhanced SpeedStep CPU.
cpu0: using only highest and lowest power states.
cpu0: Enhanced SpeedStep frequencies available (MHz): 1833 1000
cpu0: calibrating local timer
cpu0: apic clock running at 166 MHz
cpu0: 64 page colors
cpu1 at mainbus0: apid 1 (application processor)
cpu1: starting
cpu1: Intel Pentium M (Yonah) (686-class), 1828.76 MHz, id 0x6e8
cpu1: features bfe9fbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR>
cpu1: features bfe9fbff<PGE,MCA,CMOV,PAT,CFLUSH,DS,ACPI,MMX>
cpu1: features bfe9fbff<FXSR,SSE,SSE2,SS,HTT,TM,SBF>
cpu1: features2 c1a9<SSE3,MONITOR,VMX,EST,TM2,xTPR>
cpu1: "Genuine Intel(R) CPU           T2400  @ 1.83GHz"
cpu1: I-cache 32 KB 64B/line 8-way, D-cache 32 KB 64B/line 8-way
cpu1: L2 cache 2 MB 64B/line 8-way
cpu1: using thermal monitor 1
cpu1: Enhanced SpeedStep (1404 mV) 1833 MHz
cpu1: unknown Enhanced SpeedStep CPU.
cpu1: using only highest and lowest power states.
cpu1: Enhanced SpeedStep frequencies available (MHz): 1833 1000
ioapic0 at mainbus0 apid 1 (I/O APIC)
ioapic0: pa 0xfec00000, version 20, 24 pins
ioapic0: misconfigured as apic 2
ioapic0: remapped to apic 1
acpi0 at mainbus0: Advanced Configuration and Power Interface
acpi0: using Intel ACPI CA subsystem version 20060217
acpi0: X/RSDT: OemId <LENOVO,TP-7B   ,00001030>, AslId < LTP,00000000>
acpi0: found ECDT, GPE 28
acpi0: SCI interrupting at int 9
acpi0: fixed-feature power button present
timecounter: Timecounter "ACPI-Fast" frequency 3579545 Hz quality 1000
ACPI-Fast 24-bit timer
ACPI Object Type 'Processor' (0x0c) at acpi0 not configured
ACPI Object Type 'Processor' (0x0c) at acpi0 not configured
PNP0C0F at acpi0 not configured
PNP0C0F at acpi0 not configured
PNP0C0F at acpi0 not configured
PNP0C0F at acpi0 not configured
PNP0C0F at acpi0 not configured
PNP0C0F at acpi0 not configured
PNP0C0F at acpi0 not configured
PNP0C0F at acpi0 not configured
PNP0C01 at acpi0 not configured
acpilid0 at acpi0 (PNP0C0D): ACPI Lid Switch
acpibut0 at acpi0 (PNP0C0E): ACPI Sleep Button
PNP0A08 at acpi0 not configured
PNP0C02 at acpi0 not configured
PNP0000 at acpi0 not configured
attimer1 at acpi0 (PNP0100): AT Timer
attimer1: io 0x40-0x43 irq 0
PNP0103 at acpi0 not configured
PNP0200 at acpi0 not configured
pcppi1 at acpi0 (PNP0800)
pcppi1: io 0x61
pcppi1: children must have an explicit unit
midi0 at pcppi1: PC speaker (CPU-intensive output)
sysbeep0 at pcppi1
npx0 at acpi0 (PNP0C04)
npx0: io 0xf0 irq 13
npx0: reported by CPUID; using exception 16
PNP0B00 at acpi0 not configured
pckbc0 at acpi0 (PNP0303): kbd port
pckbc0: io 0x60,0x64 irq 1
pckbc1 at acpi0 (IBM3780): aux port
pckbc1: irq 12
com0 at acpi0 (IBM0071)
com0: io 0x2f8-0x2ff irq 3 drq 3
com0: ns16550a, working fifo
ATM1200 at acpi0 not configured
acpiec0 at acpi0 (PNP0C09-0): ACPI Embedded Controller
acpiec0: io 0x62,0x66
ACPI Object Type 'Power' (0x0b) at acpi0 not configured
acpibat0 at acpi0 (PNP0C0A-0): ACPI Battery (Control Method)
acpiacad0 at acpi0 (ACPI0003-0): ACPI AC Adapter
IBM0068 at acpi0 not configured
acpitz0 at acpi0: ACPI Thermal Zone
acpitz0: unable to get polling interval; using default of 30.0s
acpitz0: passive cooling mode only
acpitz0: critical 127.0C
acpitz1 at acpi0: ACPI Thermal Zone
acpitz1: unable to get polling interval; using default of 30.0s
acpitz1: critical 97.0C passive 72.0C
pcppi1: attached to attimer1
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard
pms0 at pckbc0 (aux slot)
pckbc0: using irq 12 for aux slot
wsmouse0 at pms0 mux 0
pci0 at mainbus0 bus 0: configuration mode 1
pci0: i/o space, memory space enabled, rd/line, rd/mult, wr/inv ok
pchb0 at pci0 dev 0 function 0
pchb0: vendor 0x8086 product 0x27a0 (rev. 0x03)
agp0 at pchb0: detected 7932k stolen memory
agp0: aperture at 0xd0000000, size 0x10000000
vga0 at pci0 dev 2 function 0: vendor 0x8086 product 0x27a2 (rev. 0x03)
wsdisplay0 at vga0 kbdmux 1: console (80x25, vt100 emulation), using wskbd0
wsmux1: connecting to wsdisplay0
vendor 0x8086 product 0x27a6 (miscellaneous display, revision 0x03) at pci0 dev 2 function 1 not configured
azalia0 at pci0 dev 27 function 0: Generic High Definition Audio Controller
azalia0: interrupting at ioapic0 pin 17 (irq 11)
azalia0: host: 0x8086/0x27d8 (rev. 2)
azalia0: host: High Definition Audio rev. 1.0
ppb0 at pci0 dev 28 function 0: vendor 0x8086 product 0x27d0 (rev. 0x02)
pci1 at ppb0 bus 1
pci1: i/o space, memory space enabled, rd/line, wr/inv ok
wm0 at pci1 dev 0 function 0: Intel i82573L Gigabit Ethernet, rev. 0
wm0: interrupting at ioapic0 pin 16 (irq 11)
wm0: PCI-Express bus
wm0: 256 word (8 address bits) SPI EEPROM
wm0: Ethernet address 00:16:d3:20:ce:0e
makphy0 at wm0 phy 1: Marvell 88E1111 Gigabit PHY, rev. 2
makphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto
ppb1 at pci0 dev 28 function 1: vendor 0x8086 product 0x27d2 (rev. 0x02)
pci2 at ppb1 bus 2
pci2: i/o space, memory space enabled, rd/line, wr/inv ok
wpi0 at pci2 dev 0 function 0: vendor 0x8086 product 0x4227 (rev. 0x02)
wpi0: interrupting at ioapic0 pin 17 (irq 11)
wpi0: 802.11 address 00:13:02:29:c8:c3
wpi0: 11a rates: 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps
wpi0: 11b rates: 1Mbps 2Mbps 5.5Mbps 11Mbps
wpi0: 11g rates: 1Mbps 2Mbps 5.5Mbps 11Mbps 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps
ppb2 at pci0 dev 28 function 2: vendor 0x8086 product 0x27d4 (rev. 0x02)
pci3 at ppb2 bus 3
pci3: i/o space, memory space enabled, rd/line, wr/inv ok
ppb3 at pci0 dev 28 function 3: vendor 0x8086 product 0x27d6 (rev. 0x02)
pci4 at ppb3 bus 4
pci4: i/o space, memory space enabled, rd/line, wr/inv ok
uhci0 at pci0 dev 29 function 0: vendor 0x8086 product 0x27c8 (rev. 0x02)
uhci0: interrupting at ioapic0 pin 16 (irq 11)
usb0 at uhci0: USB revision 1.0
uhub0 at usb0
uhub0: vendor 0x8086 UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
uhci1 at pci0 dev 29 function 1: vendor 0x8086 product 0x27c9 (rev. 0x02)
uhci1: interrupting at ioapic0 pin 17 (irq 11)
usb1 at uhci1: USB revision 1.0
uhub1 at usb1
uhub1: vendor 0x8086 UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
uhci2 at pci0 dev 29 function 2: vendor 0x8086 product 0x27ca (rev. 0x02)
uhci2: interrupting at ioapic0 pin 18 (irq 11)
usb2 at uhci2: USB revision 1.0
uhub2 at usb2
uhub2: vendor 0x8086 UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub2: 2 ports with 2 removable, self powered
uhci3 at pci0 dev 29 function 3: vendor 0x8086 product 0x27cb (rev. 0x02)
uhci3: interrupting at ioapic0 pin 19 (irq 11)
usb3 at uhci3: USB revision 1.0
uhub3 at usb3
uhub3: vendor 0x8086 UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub3: 2 ports with 2 removable, self powered
ehci0 at pci0 dev 29 function 7: vendor 0x8086 product 0x27cc (rev. 0x02)
ehci0: interrupting at ioapic0 pin 19 (irq 11)
ehci0: BIOS has given up ownership
ehci0: EHCI version 1.0
ehci0: companion controllers, 2 ports each: uhci0 uhci1 uhci2 uhci3
usb4 at ehci0: USB revision 2.0
uhub4 at usb4
uhub4: vendor 0x8086 EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
uhub4: 8 ports with 8 removable, self powered
ppb4 at pci0 dev 30 function 0: vendor 0x8086 product 0x2448 (rev. 0xe2)
pci5 at ppb4 bus 5
pci5: i/o space, memory space enabled
cbb0 at pci5 dev 0 function 0: vendor 0x1180 product 0x0476 (rev. 0xb4)
fwohci0 at pci5 dev 0 function 1: vendor 0x1180 product 0x0552 (rev. 0x09)
fwohci0: interrupting at ioapic0 pin 17 (irq 11)
fwohci0: OHCI version 1.0 (ROM=0)
fwohci0: No. of Isochronous channels is 4.
fwohci0: EUI64 00:0a:e4:06:00:12:20:20
fwohci0: Phy 1394a available S400, 2 ports.
fwohci0: Link S400, max_rec 2048 bytes.
ieee1394if0 at fwohci0: IEEE1394 bus
fwip0 at ieee1394if0: IP over IEEE1394
fwohci0: Initiate bus reset
vendor 0x1180 product 0x0822 (SD Host Controller system, revision 0x18) at pci5 dev 0 function 2 not configured
cbb0: interrupting at ioapic0 pin 16 (irq 11)
cardslot0 at cbb0 slot 0 flags 0
cardbus0 at cardslot0: bus 6
pcmcia0 at cardslot0
ichlpcib0 at pci0 dev 31 function 0
ichlpcib0: vendor 0x8086 product 0x27b9 (rev. 0x02)
ichlpcib0: TCO (watchdog) timer configured.
ichlpcib0: No SpeedStep
piixide0 at pci0 dev 31 function 2
piixide0: Intel 82801GBM/GHM Serial ATA Controller (ICH7) (rev. 0x02)
piixide0: bus-master DMA support present
piixide0: primary channel wired to compatibility mode
piixide0: primary channel interrupting at ioapic0 pin 14 (irq 14)
atabus0 at piixide0 channel 0
piixide0: secondary channel wired to compatibility mode
piixide0: secondary channel interrupting at ioapic0 pin 15 (irq 15)
atabus1 at piixide0 channel 1
vendor 0x8086 product 0x27da (SMBus serial bus, revision 0x02) at pci0 dev 31 function 3 not configured
isa at ichlpcib0 not configured
isa at mainbus0 not configured
ioapic0: enabling
WARNING: Callback scheduled before sysmon task queue thread present.
fwohci0: node_id=0xc800ffc0, gen=1, CYCLEMASTER mode
ieee1394if0: 1 nodes, maxhop <= 0, cable IRM = 0 (me)
ieee1394if0: bus manager 0 (me)
timecounter: Timecounter "clockinterrupt" frequency 100 Hz quality 0
azalia0: codec[0]: Analog Devices AD1981HD (rev. 2.0)
azalia0: codec[0]: High Definition Audio rev. 1.0
azalia0: playback: max channels=2, encodings=1<PCM>
azalia0: playback: PCM formats=e007f<24bit,20bit,16bit,48kHz,44.1kHz,32kHz,22.05kHz,16kHz,11.025kHz,8kHz>
azalia0: recording: max channels=2, encodings=1<PCM>
azalia0: recording: PCM formats=6007f<20bit,16bit,48kHz,44.1kHz,32kHz,22.05kHz,16kHz,11.025kHz,8kHz>
azalia0: codec[1]: 0x14f1/0x2bfa (rev. 0.0)
azalia0: codec[1]: High Definition Audio rev. 0.9
azalia0: codec[1]: No support for modem function groups
azalia0: codec[1] has no audio function groups
audio0 at azalia0: full duplex, independent
Kernelized RAIDframe activated
ubt0 at uhub3 port 1 configuration 1 interface 0
ubt0: Broadcom Corp BCM2045B, rev 2.00/1.00, addr 2
wd0 at atabus0 drive 0: <HTS541080G9SA00>
wd0: drive supports 16-sector PIO transfers, LBA48 addressing
wd0: 76319 MB, 155061 cyl, 16 head, 63 sec, 512 bytes/sect x 156301488 sectors
wd0: 32-bit data port
wd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 5 (Ultra/100)
wd0(piixide0:0:0): using PIO mode 4, Ultra-DMA mode 5 (Ultra/100) (using DMA)
boot device: wd0
root on wd0a dumps on wd0b
root file system type: ffs
cpu1: CPU 1 running
ugen0 at uhub3 port 2
ugen0: STMicroelectronics Biometric Coprocessor, rev 1.00/0.01, addr 3
wsdisplay0: screen 1 added (80x25, vt100 emulation)
wsdisplay0: screen 2 added (80x25, vt100 emulation)
wsdisplay0: screen 3 added (80x25, vt100 emulation)
wsdisplay0: screen 4 added (80x25, vt100 emulation)
wsdisplay0: screen 5 added (80x25, vt100 emulation)
Accounting started
[insert the pcmcia card..]
ath0 at cardbus0 function 0
ath0: unable to attach hardware; HAL status 13

any ideas ? may be i missed something.
>How-To-Repeat:
just insert an atheros pcmcia card into the laptop.
>Fix:
no solution yet.

NetBSD Home
NetBSD PR Database Search

(Contact us) $NetBSD: query-full-pr,v 1.39 2013/11/01 18:47:49 spz Exp $
$NetBSD: gnats_config.sh,v 1.8 2006/05/07 09:23:38 tsutsui Exp $
Copyright © 1994-2007 The NetBSD Foundation, Inc. ALL RIGHTS RESERVED.