NetBSD Problem Report #30194
From salo@Xtrmntr.org Wed May 11 09:18:57 2005
Return-Path: <salo@Xtrmntr.org>
Received: from otaku.Xtrmntr.org (sauna.silcnet.org [147.175.66.205])
by narn.netbsd.org (Postfix) with ESMTP id 0A6E763B104
for <gnats-bugs@gnats.netbsd.org>; Wed, 11 May 2005 09:18:57 +0000 (UTC)
Message-Id: <20050511091840.BFE671D102@otaku.Xtrmntr.org>
Date: Wed, 11 May 2005 11:18:40 +0200 (CEST)
From: Lubomir Sedlacik <salo@Xtrmntr.org>
Reply-To: salo@Xtrmntr.org
To: gnats-bugs@netbsd.org
Subject: unrecoverable wd(4) error after suspend/resume
X-Send-Pr-Version: 3.95
>Number: 30194
>Category: kern
>Synopsis: unrecoverable wd(4) error after suspend/resume, disk hangs
>Confidential: no
>Severity: critical
>Priority: medium
>Responsible: bouyer
>State: closed
>Class: sw-bug
>Submitter-Id: net
>Arrival-Date: Wed May 11 09:19:00 +0000 2005
>Closed-Date: Wed Jul 05 17:07:22 +0000 2006
>Last-Modified: Wed Jul 05 17:07:22 +0000 2006
>Originator: Lubomir Sedlacik
>Release: NetBSD 3.99.3, sources as of May 10 2005
>Organization:
>Environment:
System: NetBSD 3.99.3
Architecture: i386
Machine: i386
Model: IBM ThinkPad X40
>Description:
i am unable to resume from suspend with APM in the kernel. when resuming, the
system comes up but disk seems to be hung immediately (sometimes the disk
activity led is constantly on), processes hang in vnlock (sometimes in
getblk). kernel prints error:
atabus0: resuming...
atabus1: resuming...
wd0a: error writing fsbn 15042624 of 15042624-15042655 (wd0 bn 15042687; cn 14923 tn 4 sn 51), retrying
wd0: (aborted command)
and:
wm0: device timeout (txfree 4058 txsfree 35 txnext 280
but the network comes up few seconds later and e.g., ssh connection is
resumed.
i tested various BIOS settings (e.g., disabling PCI Power Management) and
apm(4) options (e.g., APM_DISABLE_INTERRUPTS=0, APM_NO_IDLE) without any
effect.
my setup is a bit nonstandard, the whole hard drive is a cgd(4) volume on top
of wd0a; if it matters. kernel boots from usb and while i am in single-user
in md(4), suspend/resume seems to work without any problems (until the system
is booted into multi-user involving disk activity, up until then the hard
drive is not touched apart of kernel probing it at boot time). unfortunately,
i can't test with plain file system due to the nature of my installation.
>How-To-Repeat:
try to suspend/resume -current on X40,
see disk hang immediately after resuming
>Fix:
n/a
- missing power hook somewhere in the piixide(4) or wd(4) code?
- could cgd(4) affect the situation?
>Release-Note:
>Audit-Trail:
From: Lubomir Sedlacik <salo@Xtrmntr.org>
To: gnats-bugs@netbsd.org
Cc:
Subject: Re: kern/30194: unrecoverable wd(4) error after suspend/resume
Date: Wed, 11 May 2005 12:04:54 +0200
--W/nzBZO5zC0uMSeA
Content-Type: text/plain; charset=us-ascii
Content-Disposition: inline
Content-Transfer-Encoding: quoted-printable
i verified that cgd(4) is unrelated to the issue. in single-user mode i
newfs-ed swap partition (in multi-user it's also a cgd(4) volume),
mounted it and created a couple of files on it and suspend/resumed. no
cgd devices were configured at that time. the same error occured and
disk hung.
--=20
-- Lubomir Sedlacik <salo@{NetBSD,Xtrmntr,silcnet}.org> --
--W/nzBZO5zC0uMSeA
Content-Type: application/pgp-signature
Content-Disposition: inline
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.2.6 (NetBSD)
iD8DBQFCgdjFiwjDDlS8cmMRAljuAJ9GbK+EM7hi10jHvY6Mwpez/g0VxQCePfaF
Cdrt45uICmdi97km767QaNA=
=x5Fu
-----END PGP SIGNATURE-----
--W/nzBZO5zC0uMSeA--
From: Lubomir Sedlacik <salo@Xtrmntr.org>
To: gnats-bugs@netbsd.org
Cc:
Subject: Re: kern/30194: unrecoverable wd(4) error after suspend/resume
Date: Wed, 11 May 2005 13:36:05 +0200
--MfFXiAuoTsnnDAfZ
Content-Type: text/plain; charset=us-ascii
Content-Disposition: inline
appending dmesg and kernel config.
--
-- Lubomir Sedlacik <salo@{NetBSD,Xtrmntr,silcnet}.org> --
--MfFXiAuoTsnnDAfZ
Content-Type: text/plain; charset=us-ascii
Content-Disposition: attachment; filename=dmesg
Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005
The NetBSD Foundation, Inc. All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
The Regents of the University of California. All rights reserved.
NetBSD 3.99.3 (AURORA-SURREALIS) #3: Wed May 11 12:27:52 CEST 2005
salo@aurora-surrealis:/opt/obj/sys/arch/i386/compile/AURORA-SURREALIS
total memory = 502 MB
avail memory = 484 MB
BIOS32 rev. 0 found at 0xfd740
PCI BIOS rev. 2.1 found at 0xfd8c8
PCI IRQ Routing Table rev. 1.0 found at 0xfdeb0, size 256 bytes (14 entries)
PCI Interrupt Router at 000:31:0 (Intel 82371FB (PIIX) PCI-ISA Bridge compatible)
pci_addr_fixup: 000:31:1 0x8086 0x24ca new address 0x00005800
pci_addr_fixup: 000:31:1 0x8086 0x24ca new address 0x00005808
pci_addr_fixup: 000:31:1 0x8086 0x24ca new address 0x00005810
pci_addr_fixup: 000:31:1 0x8086 0x24ca new address 0x0000580c
pci_addr_fixup: 000:31:1 0x8086 0x24ca new address 0x1f700000
mainbus0 (root)
cpu0 at mainbus0: (uniprocessor)
cpu0: Intel Pentium M (Dothan) (686-class), 1395.53 MHz, id 0x6d6
cpu0: features afe9fbbf<FPU,VME,DE,PSE,TSC,MSR,MCE,CX8,APIC,SEP,MTRR>
cpu0: features afe9fbbf<PGE,MCA,CMOV,PAT,CFLUSH,DS,ACPI,MMX>
cpu0: features afe9fbbf<FXSR,SSE,SSE2,SS,TM,SBF>
cpu0: features2 180<EST,TM2>
cpu0: "Intel(R) Pentium(R) M processor 1.40GHz"
cpu0: using thermal monitor 2
cpu0: Enhanced SpeedStep running at 1400 MHz (1116 mV)
cpu0: Enhanced SpeedStep frequencies available (MHz): 1400 1300 1200 1100 1000 900 800 600
pci0 at mainbus0 bus 0: configuration mode 1
pci0: i/o space, memory space enabled, rd/line, rd/mult, wr/inv ok
pchb0 at pci0 dev 0 function 0
pchb0: Intel 82855GM Host-Hub Controller (rev. 0x02)
agp0 at pchb0: detected 8060k stolen memory
agp0: aperture at 0xe0000000, size 0x8000000
Intel 82855GM GMCH Memory Controller (miscellaneous system, revision 0x02) at pci0 dev 0 function 1 not configured
Intel 82855GM GMCH Configuration Process (miscellaneous system, revision 0x02) at pci0 dev 0 function 3 not configured
vga0 at pci0 dev 2 function 0: Intel 82855GM GMCH Integrated Graphics Device (rev. 0x02)
wsdisplay0 at vga0 kbdmux 1: console (80x25, vt100 emulation)
wsmux1: connecting to wsdisplay0
Intel 82855GM GMCH Integrated Graphics Device (miscellaneous display, revision 0x02) at pci0 dev 2 function 1 not configured
uhci0 at pci0 dev 29 function 0: Intel 82801DB USB UHCI Controller (rev. 0x01)
uhci0: interrupting at irq 9
usb0 at uhci0: USB revision 1.0
uhub0 at usb0
uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
uhci1 at pci0 dev 29 function 1: Intel 82801DB USB UHCI Controller (rev. 0x01)
uhci1: interrupting at irq 11
usb1 at uhci1: USB revision 1.0
uhub1 at usb1
uhub1: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
uhci2 at pci0 dev 29 function 2: Intel 82801DB USB UHCI Controller (rev. 0x01)
uhci2: interrupting at irq 10
usb2 at uhci2: USB revision 1.0
uhub2 at usb2
uhub2: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub2: 2 ports with 2 removable, self powered
ehci0 at pci0 dev 29 function 7: Intel 82801DB USB EHCI Controller (rev. 0x01)
ehci0: interrupting at irq 9
ehci0: EHCI version 1.0
ehci0: companion controllers, 2 ports each: uhci0 uhci1 uhci2
usb3 at ehci0: USB revision 2.0
uhub3 at usb3
uhub3: Intel EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
uhub3: 6 ports with 6 removable, self powered
ppb0 at pci0 dev 30 function 0: Intel 82801BAM Hub-PCI Bridge (rev. 0x81)
pci1 at ppb0 bus 1
pci1: i/o space, memory space enabled
cbb0 at pci1 dev 0 function 0: Ricoh 5C476 PCI-CardBus bridge (rev. 0x8d)
Ricoh product 0x0822 (system subclass 0x05, revision 0x13) at pci1 dev 0 function 1 not configured
wm0 at pci1 dev 1 function 0: Intel i82541GI Mobile 1000BASE-T Ethernet, rev. 0
wm0: interrupting at irq 4
wm0: 32-bit 33MHz PCI bus
wm0: 64 word (6 address bits) MicroWire EEPROM
wm0: Ethernet address 00:0a:e4:2d:4d:21
igphy0 at wm0 phy 1: Intel IGP01E1000 Gigabit PHY, rev. 0
igphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto
iwi0 at pci1 dev 2 function 0: Intel PRO/Wireless LAN 2200BG Mini-PCI Adapter (rev. 0x05)
iwi0: interrupting at irq 6
iwi0: 802.11 address 00:0e:35:f1:2b:9a
iwi0: 11b rates: 1Mbps 2Mbps 5.5Mbps 11Mbps
iwi0: 11g rates: 1Mbps 2Mbps 5.5Mbps 11Mbps 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps
cbb0: interrupting at irq 9
cardslot0 at cbb0 slot 0 flags 0
cardbus0 at cardslot0: bus 2 device 0
pcmcia0 at cardslot0
pcib0 at pci0 dev 31 function 0
pcib0: Intel 82801DB ISA Bridge (rev. 0x01)
piixide0 at pci0 dev 31 function 1
piixide0: Intel 82801DBM IDE Controller (ICH4-M) (rev. 0x01)
piixide0: bus-master DMA support present
piixide0: primary channel wired to compatibility mode
piixide0: primary channel interrupting at irq 14
atabus0 at piixide0 channel 0
piixide0: secondary channel wired to compatibility mode
piixide0: secondary channel interrupting at irq 15
atabus1 at piixide0 channel 1
Intel 82801DB SMBus Controller (SMBus serial bus, revision 0x01) at pci0 dev 31 function 3 not configured
auich0 at pci0 dev 31 function 5: i82801DB/DBM (ICH4/ICH4M) AC-97 Audio
auich0: interrupting at irq 5
auich0: ac97: Analog Devices AD1981B codec; headphone, 20 bit DAC, no 3D stereo
auich0: ac97: ext id 601<AC97_22,AMAP,VRA>
Intel 82801DB AC97 Modem Controller (modem communications, revision 0x01) at pci0 dev 31 function 6 not configured
isa0 at pcib0
com0 at isa0 port 0x2f8-0x2ff irq 3: ns16550a, working fifo
pckbc0 at isa0 port 0x60-0x64
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
pms0 at pckbc0 (aux slot)
pckbc0: using irq 12 for aux slot
wsmouse0 at pms0 mux 0
attimer0 at isa0 port 0x40-0x43: AT Timer
pcppi0 at isa0 port 0x61
midi0 at pcppi0: PC speaker
spkr0 at pcppi0
sysbeep0 at pcppi0
npx0 at isa0 port 0xf0-0xff: using exception 16
pcppi0: attached to attimer0
apm0 at mainbus0: Power Management spec V1.2
apm0: battery life expectancy: 97%
apm0: A/C state: on
apm0: battery charge state: high
auich0: measured ac97 link rate at 48003 Hz, will use 48000 Hz
audio0 at auich0: full duplex, mmap, independent
md0: internal 3000 KB image area
IPsec: Initialized Security Association Processing.
wd0 at atabus0 drive 0: <HITACHI_DK13FA-40B>
wd0: drive supports 16-sector PIO transfers, LBA addressing
wd0: 38154 MB, 77520 cyl, 16 head, 63 sec, 512 bytes/sect x 78140160 sectors
wd0: 32-bit data port
wd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 5 (Ultra/100)
wd0(piixide0:0:0): using PIO mode 4, Ultra-DMA mode 5 (Ultra/100) (using DMA)
boot device: <unknown>
root on md0a dumps on md0b
wsdisplay0: screen 1 added (80x25, vt100 emulation)
wsdisplay0: screen 2 added (80x25, vt100 emulation)
wsdisplay0: screen 3 added (80x25, vt100 emulation)
wsdisplay0: screen 4 added (80x25, vt100 emulation)
--MfFXiAuoTsnnDAfZ
Content-Type: text/plain; charset=us-ascii
Content-Disposition: attachment; filename=AURORA-SURREALIS
# AURORA-SURREALIS -- IBM ThinkPad X40
#
include "arch/i386/conf/std.i386"
options INCLUDE_CONFIG_FILE # embed config file in kernel binary
# Enable the hooks used for initializing the root memory-disk.
options MEMORY_DISK_HOOKS
options MEMORY_DISK_IS_ROOT # force root on memory disk
options MEMORY_DISK_SERVER=0 # no userspace memory disk support
options MEMORY_DISK_ROOT_SIZE=6000 # size of memory disk, in blocks
options MEMORY_RBFLAGS=0
maxusers 64 # estimated number of users
# CPU support. At least one is REQUIRED.
options I686_CPU
# CPU-related options.
options VM86 # virtual 8086 emulation
options USER_LDT # user-settable LDT; used by WINE
# Enhanced SpeedStep Technology in the Pentium M
options ENHANCED_SPEEDSTEP
options MTRR # memory-type range register syscall support
# Standard system options
options INSECURE # disable kernel security levels - X needs this
options RTC_OFFSET=0 # hardware clock is this many mins. west of GMT
options NTP # NTP phase/frequency locked loop
options KTRACE # system call tracing via ktrace(1)
options SYSTRACE # system call vetting via systrace(1)
options SYSVMSG # System V-like message queues
options SYSVSEM # System V-like semaphores
options SYSVSHM # System V-like memory sharing
options SHMMAXPGS=65536 # 2048 pages is the default
options P1003_1B_SEMAPHORE # p1003.1b semaphore support
options LKM # loadable kernel modules
options USERCONF # userconf(4) support
options SYSCTL_INCLUDE_DESCR # Include sysctl descriptions in kernel
# Diagnostic/debugging support options
options DDB # in-kernel debugger
options DDB_HISTORY_SIZE=512 # enable history editing in DDB
# Compatibility options
options COMPAT_16 # NetBSD 1.6
options COMPAT_20 # NetBSD 2.0
options COMPAT_OSSAUDIO # OSS (Voxware) audio driver compatibility
options COMPAT_LINUX # binary compatibility with Linux
options COMPAT_BSDPTY # /dev/[pt]ty?? ptys.
# File systems
file-system FFS # UFS
file-system EXT2FS # second extended file system (linux)
file-system LFS # log-structured file system
file-system MFS # memory file system
file-system NFS # Network File System client
file-system NTFS # Windows/NT file system (experimental)
file-system CD9660 # ISO 9660 + Rock Ridge file system
file-system MSDOSFS # MS-DOS file system
file-system FDESC # /dev/fd
file-system KERNFS # /kern
file-system NULLFS # loopback file system
file-system OVERLAY # overlay file system
file-system PORTAL # portal filesystem (still experimental)
file-system PROCFS # /proc
file-system UMAPFS # NULLFS + uid and gid remapping
file-system UNION # union file system
file-system SMBFS # experimental - CIFS; also needs nsmb (below)
file-system PTYFS # pseudo-terminal filesystem
# File system options
options SOFTDEP # FFS soft updates support.
options NFSSERVER # Network File System server
# Networking options
options GATEWAY # packet forwarding
options INET # IP + ICMP + TCP + UDP
options INET6 # IPV6
options IPSEC # IP security
options IPSEC_ESP # IP security (encryption part; define w/IPSEC)
options PPP_BSDCOMP # BSD-Compress compression support for PPP
options PPP_DEFLATE # Deflate compression support for PPP
options PPP_FILTER # Active filter support for PPP (requires bpf)
options PFIL_HOOKS # pfil(9) packet filter hooks
options IPFILTER_LOG # ipmon(8) log support
# These options enable verbose messages for several subsystems.
# Warning, these may compile large string tables into the kernel!
options MIIVERBOSE # verbose PHY autoconfig messages
options PCIVERBOSE # verbose PCI device autoconfig messages
#options PCMCIAVERBOSE # verbose PCMCIA configuration messages
options SCSIVERBOSE # human readable SCSI error messages
options USBVERBOSE # verbose USB device autoconfig messages
options NFS_BOOT_DHCP,NFS_BOOT_BOOTPARAM
# wscons options
#
# builtin terminal emulations
options WSEMUL_VT100 # VT100 / VT220 emulation
# customization of console and kernel output - see dev/wscons/wsdisplayvar.h
options WSDISPLAY_CUSTOM_OUTPUT # color customization from wsconsctl(8)
options WS_KERNEL_FG=WSCOL_CYAN
# customization of console border color
options WSDISPLAY_CUSTOM_BORDER # border customization from wsconsctl(8)
# compatibility to other console drivers
options WSDISPLAY_COMPAT_PCVT # emulate some ioctls
options WSDISPLAY_COMPAT_SYSCONS # emulate some ioctls
options WSDISPLAY_COMPAT_USL # VT handling
options WSDISPLAY_COMPAT_RAWKBD # can get raw scancodes
# use a large software cursor that doesn't blink
options PCDISPLAY_SOFTCURSOR
# Kernel root file system and dump configuration.
config netbsd root on md0a type ffs
#
# Device configuration
#
mainbus0 at root
cpu0 at mainbus0
apm0 at mainbus0 # Advanced power management
# Tuning for power management, see apm(4) for more details.
options APM_NO_IDLE # Don't call BIOS CPU idle function
options APM_POWER_PRINT # Print stats on the console
options APM_DISABLE_INTERRUPTS=0 # Don't disable interrupts
# Basic Bus Support
#
# PCI bus support
pci* at mainbus? bus ?
pci* at ppb? bus ?
# Configure PCI using BIOS information
options PCIBIOS # PCI BIOS support
#options PCIBIOSVERBOSE # PCI BIOS verbose info
options PCIBIOS_ADDR_FIXUP # fixup PCI I/O addresses
options PCIBIOS_BUS_FIXUP # fixup PCI bus numbering
options PCIBIOS_INTR_FIXUP # fixup PCI interrupt routing
#options PCIBIOS_IRQS_HINT=0x0a00 # PCI interrupts hint. IRQ 9 or 11
#options PCIBIOS_INTR_GUESS # see pcibios(4)
#options PCIINTR_DEBUG # super-verbose PCI interrupt fixup
# PCI bridges
pchb* at pci? dev ? function ? # PCI-Host bridges
pcib* at pci? dev ? function ? # PCI-ISA bridges
ppb* at pci? dev ? function ? # PCI-PCI bridges
agp* at pchb?
# ISA bus support
isa0 at pcib?
# CardBus bridge support
cbb* at pci? dev ? function ?
cardslot* at cbb?
# CardBus bus support
cardbus* at cardslot?
pcmcia* at cardslot?
# Coprocessor Support
#
# Math Coprocessor support
npx0 at isa? port 0xf0 irq 13 # x86 math coprocessor
# Console Devices
#
# wscons
pckbc0 at isa? # pc keyboard controller
pckbd* at pckbc? # PC keyboard
pms* at pckbc? # PS/2 mouse for wsmouse
vga* at pci? dev ? function ?
wsdisplay* at vga? console ?
wskbd* at pckbd? console ?
wsmouse* at pms? mux 0
attimer0 at isa?
pcppi0 at isa?
sysbeep0 at pcppi?
# Serial Devices
#
# PCMCIA serial interfaces
com* at pcmcia? function ? # Modems and serial cards
# CardBus serial interfaces
com* at cardbus? dev ? function ? # Modems and serial cards
# ISA serial interfaces
com0 at isa? port 0x2f8 irq 3
# SCSI Controllers and Devices
#
# SCSI bus support
scsibus* at scsi?
# SCSI devices
sd* at scsibus? target ? lun ? # SCSI disk drives
cd* at scsibus? target ? lun ? # SCSI CD-ROM drives
uk* at scsibus? target ? lun ? # SCSI unknown
# IDE and related devices
#
# PCI IDE controllers - see pciide(4) for supported hardware.
# The 0x0001 flag force the driver to use DMA, even if the driver doesn't know
# how to set up DMA modes for this chip. This may work, or may cause
# a machine hang with some controllers.
piixide* at pci? dev ? function ? # Intel IDE controllers
# ATA (IDE) bus support
atabus* at ata?
# IDE drives
# Flags are used only with controllers that support DMA operations
# and mode settings (e.g. some pciide controllers)
# The lowest order four bits (rightmost digit) of the flags define the PIO
# mode to use, the next set of four bits the DMA mode and the third set the
# UltraDMA mode. For each set of four bits, the 3 lower bits define the mode
# to use, and the last bit must be 1 for this setting to be used.
# For DMA and UDMA, 0xf (1111) means 'disable'.
# 0x0fac means 'use PIO mode 4, DMA mode 2, disable UltraDMA'.
# (0xc=1100, 0xa=1010, 0xf=1111)
# 0x0000 means "use whatever the drive claims to support".
wd* at atabus? drive ? flags 0x0000
# ATAPI bus support
atapibus* at atapi?
# ATAPI devices
#
# flags have the same meaning as for IDE drives.
cd* at atapibus? drive ? flags 0x0000 # ATAPI CD-ROM drives
sd* at atapibus? drive ? flags 0x0000 # ATAPI disk drives
uk* at atapibus? drive ? flags 0x0000 # ATAPI unknown
# Network Interfaces
#
# PCI network interfaces
ath* at pci? dev ? function ? # Atheros 5210/5211/5212 802.11
iwi* at pci? dev ? function ? # Intel PRO/Wireless 2200BG
wm* at pci? dev ? function ? # Intel 8254x gigabit
# PCMCIA network interfaces
an* at pcmcia? function ? # Aironet PC4500/PC4800 (802.11)
awi* at pcmcia? function ? # BayStack 650/660 (802.11FH/DS)
cnw* at pcmcia? function ? # Xircom/Netwave AirSurfer
ray* at pcmcia? function ? # Raytheon Raylink (802.11)
wi* at pcmcia? function ? # Lucent/Intersil WaveLan IEEE (802.11)
# CardBus network cards
ath* at cardbus? dev ? function ? # Atheros 5210/5211/5212 802.11
atw* at cardbus? dev ? function ? # ADMtek ADM8211 (802.11)
ex* at cardbus? dev ? function ? # 3Com 3C575TX
fxp* at cardbus? dev ? function ? # Intel i8255x
re* at cardbus? dev ? function ? # Realtek 8139C+/8169/8169S/8110S
rtk* at cardbus? dev ? function ? # Realtek 8129/8139
tlp* at cardbus? dev ? function ? # DECchip 21143
# MII/PHY support
brgphy* at mii? phy ? # Broadcom BCM5400-family PHYs
dmphy* at mii? phy ? # Davicom DM9101 PHYs
exphy* at mii? phy ? # 3Com internal PHYs
icsphy* at mii? phy ? # Integrated Circuit Systems ICS189x
igphy* at mii? phy ? # Intel IGP01E1000
inphy* at mii? phy ? # Intel 82555 PHYs
iophy* at mii? phy ? # Intel 82553 PHYs
lxtphy* at mii? phy ? # Level One LXT-970 PHYs
makphy* at mii? phy ? # Marvell Semiconductor 88E1000 PHYs
nsphy* at mii? phy ? # NS83840 PHYs
nsphyter* at mii? phy ? # NS83843 PHYs
qsphy* at mii? phy ? # Quality Semiconductor QS6612 PHYs
rgephy* at mii? phy ? # Realtek 8169S/8110 internal PHYs
sqphy* at mii? phy ? # Seeq 80220/80221/80223 PHYs
tlphy* at mii? phy ? # ThunderLAN PHYs
tqphy* at mii? phy ? # TDK Semiconductor PHYs
ukphy* at mii? phy ? # generic unknown PHYs
# USB Controller and Devices
#
# PCI USB controllers
ehci* at pci? dev ? function ? # Enhanced Host Controller
uhci* at pci? dev ? function ? # Universal Host Controller (Intel)
# CardBus USB controllers
ehci* at cardbus? dev ? function ? # Enhanced Host Controller
ohci* at cardbus? dev ? function ? # Open Host Controller
# USB bus support
usb* at ehci?
usb* at ohci?
usb* at uhci?
# USB Hubs
uhub* at usb?
uhub* at uhub? port ? configuration ? interface ?
# USB HID device
uhidev* at uhub? port ? configuration ? interface ?
# USB Mice
ums* at uhidev? reportid ?
wsmouse* at ums? mux 0
# USB Keyboards
ukbd* at uhidev? reportid ?
wskbd* at ukbd? console ? mux 1
# USB Generic HID devices
uhid* at uhidev? reportid ?
# USB Printer
ulpt* at uhub? port ? configuration ? interface ?
# USB Modem
umodem* at uhub? port ? configuration ?
ucom* at umodem?
# USB Mass Storage
umass* at uhub? port ? configuration ? interface ?
wd* at umass?
# USB audio
uaudio* at uhub? port ? configuration ?
# USB MIDI
umidi* at uhub? port ? configuration ?
# USB IrDA
# USB-IrDA bridge spec
uirda* at uhub? port ? configuration ? interface ?
irframe* at uirda?
# SigmaTel STIr4200 USB/IrDA Bridge
ustir* at uhub? port ?
irframe* at ustir?
# USB Ethernet adapters
aue* at uhub? port ? # ADMtek AN986 Pegasus based adapters
axe* at uhub? port ? # ASIX AX88172 based adapters
cue* at uhub? port ? # CATC USB-EL1201A based adapters
kue* at uhub? port ? # Kawasaki LSI KL5KUSB101B based adapters
url* at uhub? port ? # Realtek RTL8150L based adapters
# Prolofic PL2301/PL2302 host-to-host adapter
upl* at uhub? port ?
# Serial adapters
#
# FTDI FT8U100AX serial adapter
uftdi* at uhub? port ?
ucom* at uftdi? portno ?
uplcom* at uhub? port ? # I/O DATA USB-RSAQ2 serial adapter
ucom* at uplcom? portno ?
umct* at uhub? port ? # MCT USB-RS232 serial adapter
ucom* at umct? portno ?
# USB Generic driver
ugen* at uhub? port ?
# Audio Devices
#
# PCI audio devices
auich* at pci? dev ? function ? # Intel ICH integrated AC'97 Audio
# Audio support
audio* at audiobus?
# MIDI support
midi* at midibus?
midi* at pcppi? # MIDI interface to the PC speaker
# The spkr driver provides a simple tone interface to the built in speaker.
spkr0 at pcppi? # PC speaker
# Pseudo-Devices
#
# disk/mass storage pseudo-devices
pseudo-device ccd 4 # concatenated/striped disk devices
pseudo-device cgd 4 # cryptographic disk devices
pseudo-device fss 4 # file system snapshot device
pseudo-device md 1 # memory disk device (ramdisk)
pseudo-device vnd 4 # disk-like interface to files
# network pseudo-devices
pseudo-device bpfilter 8 # Berkeley packet filter
pseudo-device ipfilter # IP filter (firewall) and NAT
pseudo-device loop # network loopback
pseudo-device ppp 2 # Point-to-Point Protocol
pseudo-device pppoe # PPP over Ethernet (RFC 2516)
pseudo-device irframetty # IrDA frame line discipline
pseudo-device tun 2 # network tunneling over tty
pseudo-device tap # virtual Ethernet
pseudo-device gre 2 # generic L3 over IP tunnel
pseudo-device gif 4 # IPv[46] over IPv[46] tunnel (RFC1933)
pseudo-device vlan # IEEE 802.1q encapsulation
pseudo-device bridge # simple inter-network bridging
# miscellaneous pseudo-devices
pseudo-device pty # pseudo-terminals
pseudo-device sequencer 1 # MIDI sequencer
pseudo-device rnd # /dev/random and in-kernel generator
pseudo-device clockctl # user control of clock subsystem
pseudo-device ksyms # /dev/ksyms
# a pseudo device needed for SMBFS
pseudo-device nsmb # experimental - SMB requester
# wscons pseudo-devices
pseudo-device wsmux # mouse & keyboard multiplexor
pseudo-device wsfont
--MfFXiAuoTsnnDAfZ--
From: Lubomir Sedlacik <salo@Xtrmntr.org>
To: gnats-bugs@netbsd.org
Cc:
Subject: Re: kern/30194: unrecoverable wd(4) error after suspend/resume
Date: Thu, 12 May 2005 21:50:54 +0200
more information:
- it doesn't happen with 2.0.2
- it doesn't happen with 3.0_BETA
- it happens with the recent 200505090000Z snapshot of 3.99.3,
these errors are printed out (netbsd-INSTALL_LAPTOP):
piixide0:0:0: lost interrupt
type: ata tc_bcount: 2040 tc_skip: 0
piixide0:0:0: bus-master DMA error: missing interrupt, status=0x1
and the drive activity LED is on, disk is hung.
--
-- Lubomir Sedlacik <salo@{NetBSD,Xtrmntr,silcnet}.org> --
From: Lubomir Sedlacik <salo@Xtrmntr.org>
To: gnats-bugs@netbsd.org
Cc:
Subject: Re: kern/30194: unrecoverable wd(4) error after suspend/resume
Date: Fri, 13 May 2005 11:39:01 +0200
ok, spoke too soon.
it actually hangs on all of netbsd-2-0, netbsd-2, netbsd-3 and -current
if i leave it suspended for a longer time (e.g., 1 minute).
i tried INSTALL_LAPTOP kernels from netbsd-2 (may 11th snapshot),
netbsd-2-0 (2.0.2 release), netbsd-3 (may 6th) and various -current
sources (may 12th, jan 25th, jan 1st - both INSTALL_LAPTOP and my custom
configs).
--
-- Lubomir Sedlacik <salo@{NetBSD,Xtrmntr,silcnet}.org> --
From: Manuel Bouyer <bouyer@antioche.eu.org>
To: gnats-bugs@NetBSD.org
Cc: kern-bug-people@NetBSD.org, gnats-admin@NetBSD.org,
netbsd-bugs@NetBSD.org
Subject: Re: kern/30194: unrecoverable wd(4) error after suspend/resume
Date: Mon, 16 May 2005 20:02:05 +0200
--17pEHd4RhPHOinZp
Content-Type: text/plain; charset=us-ascii
Content-Disposition: inline
> >Description:
> i am unable to resume from suspend with APM in the kernel. when resuming, the
> system comes up but disk seems to be hung immediately (sometimes the disk
> activity led is constantly on), processes hang in vnlock (sometimes in
> getblk). kernel prints error:
>
> atabus0: resuming...
> atabus1: resuming...
> wd0a: error writing fsbn 15042624 of 15042624-15042655 (wd0 bn 15042687; cn 14923 tn 4 sn 51), retrying
> wd0: (aborted command)
Hi,
can you try the attached patch ? I've not been able to reproduce your problem,
but the atabus power hook needs to be smarter than it is actually.
--
Manuel Bouyer <bouyer@antioche.eu.org>
NetBSD: 26 ans d'experience feront toujours la difference
--
--17pEHd4RhPHOinZp
Content-Type: text/plain; charset=us-ascii
Content-Disposition: attachment; filename=diff
Index: ata.c
===================================================================
RCS file: /cvsroot/src/sys/dev/ata/ata.c,v
retrieving revision 1.67
diff -u -r1.67 ata.c
--- ata.c 11 Apr 2005 04:24:54 -0000 1.67
+++ ata.c 16 May 2005 17:42:45 -0000
@@ -158,6 +158,7 @@
TAILQ_INIT(&chp->ch_queue->queue_xfer);
chp->ch_queue->queue_freeze = 0;
+ chp->ch_queue->queue_flags = 0;
chp->ch_queue->active_xfer = NULL;
chp->atabus = config_found(&chp->ch_atac->atac_dev, chp, atabusprint);
@@ -322,11 +323,7 @@
splx(s);
/* Configure the devices on the bus. */
- if (sc->sc_sleeping == 1) {
- printf("%s: resuming...\n", sc->sc_dev.dv_xname);
- sc->sc_sleeping = 0;
- } else
- atabusconfig(sc);
+ atabusconfig(sc);
for (;;) {
s = splbio();
@@ -430,7 +427,6 @@
config_pending_incr();
kthread_create(atabus_create_thread, sc);
- sc->sc_sleeping = 0;
sc->sc_powerhook = powerhook_establish(atabus_powerhook, sc);
if (sc->sc_powerhook == NULL)
printf("%s: WARNING: unable to establish power hook\n",
@@ -699,6 +695,22 @@
}
/*
+ * freeze the queue and wait for the controller to be idle. Caller has to
+ * unfreeze/restart the queue
+ */
+void
+ata_queue_idle(struct ata_queue *queue)
+{
+ int s = splbio();
+ queue->queue_freeze++;
+ while (queue->active_xfer != NULL) {
+ queue->queue_flags |= QF_IDLE_WAIT;
+ tsleep(&queue->queue_flags, PRIBIO, "qidl", 0);
+ }
+ splx(s);
+}
+
+/*
* Add a command to the queue and start controller.
*
* MUST BE CALLED AT splbio()!
@@ -772,6 +784,10 @@
return; /* channel aleady active */
}
if (__predict_false(chp->ch_queue->queue_freeze > 0)) {
+ if (queue->queue_flags & QF_IDLE_WAIT) {
+ queue->queue_flags &= ~QF_IDLE_WAIT;
+ wakeup(&queue->queue_flags);
+ }
return; /* queue froozen */
}
/*
@@ -1422,17 +1438,17 @@
switch (why) {
case PWR_SOFTSUSPEND:
case PWR_SOFTSTANDBY:
- sc->sc_sleeping = 1;
- s = splbio();
- chp->ch_flags = ATACH_SHUTDOWN;
- splx(s);
- wakeup(&chp->ch_thread);
- while (chp->ch_thread != NULL)
- (void) tsleep((void *)&chp->ch_flags, PRIBIO,
- "atadown", 0);
+ /* freeze the queue and wait for the controller to be idle */
+ ata_queue_idle(chp->ch_queue);
break;
case PWR_RESUME:
- atabus_create_thread(sc);
+ printf("%s: resuming...\n", sc->sc_dev.dv_xname);
+ s = splbio();
+ KASSERT(chp->ch_queue->queue_freeze > 0);
+ /* unfreeze the queue and reset drives (to wake them up) */
+ chp->ch_queue->queue_freeze--;
+ ata_reset_channel(chp, AT_WAIT);
+ splx(s);
break;
case PWR_SUSPEND:
case PWR_STANDBY:
Index: atavar.h
===================================================================
RCS file: /cvsroot/src/sys/dev/ata/atavar.h,v
retrieving revision 1.67
diff -u -r1.67 atavar.h
--- atavar.h 27 Feb 2005 00:26:59 -0000 1.67
+++ atavar.h 16 May 2005 17:42:45 -0000
@@ -88,6 +88,8 @@
TAILQ_HEAD(, ata_xfer) queue_xfer; /* queue of pending commands */
int queue_freeze; /* freeze count for the queue */
struct ata_xfer *active_xfer; /* active command */
+ int queue_flags; /* flags for this queue */
+#define QF_IDLE_WAIT 0x01 /* someone is wants the controller idle */
};
/* ATA bus instance state information. */
@@ -97,7 +99,6 @@
int sc_flags;
#define ATABUSCF_OPEN 0x01
void *sc_powerhook;
- int sc_sleeping;
};
/*
@@ -441,6 +442,7 @@
void ata_probe_caps(struct ata_drive_datas *);
void ata_dmaerr(struct ata_drive_datas *, int);
+void ata_queue_idle(struct ata_queue *);
#endif /* _KERNEL */
#endif /* _DEV_ATA_ATAVAR_H_ */
--17pEHd4RhPHOinZp--
From: Lubomir Sedlacik <salo@Xtrmntr.org>
To: Manuel Bouyer <bouyer@antioche.eu.org>
Cc: gnats-bugs@netbsd.org
Subject: Re: kern/30194: unrecoverable wd(4) error after suspend/resume
Date: Mon, 16 May 2005 22:28:46 +0200
--9wW02hG+pBvRTRBg
Content-Type: text/plain; charset=us-ascii
Content-Disposition: inline
Content-Transfer-Encoding: quoted-printable
hi,
On Mon, May 16, 2005 at 08:02:05PM +0200, Manuel Bouyer wrote:
> can you try the attached patch ? I've not been able to reproduce your
> problem, but the atabus power hook needs to be smarter than it is
> actually.
whooa! this made a whole lot of a difference (after fixing your patch
to compile :). i am now able to suspend/resume without disk losing
interrupts and hanging. thanks a lot!
patch for your patch (i also fixed a typo in a comment):
--- ata.diff.orig 2005-05-16 20:34:50.000000000 +0200
+++ ata.diff 2005-05-16 22:17:06.000000000 +0200
@@ -57,17 +57,19 @@
* Add a command to the queue and start controller.
*
* MUST BE CALLED AT splbio()!
-@@ -772,6 +784,10 @@
+@@ -772,7 +784,11 @@
return; /* channel aleady active */
}
if (__predict_false(chp->ch_queue->queue_freeze > 0)) {
-+ if (queue->queue_flags & QF_IDLE_WAIT) {
-+ queue->queue_flags &=3D ~QF_IDLE_WAIT;
-+ wakeup(&queue->queue_flags);
+- return; /* queue froozen */
++ if (chp->ch_queue->queue_flags & QF_IDLE_WAIT) {
++ chp->ch_queue->queue_flags &=3D ~QF_IDLE_WAIT;
++ wakeup(&chp->ch_queue->queue_flags);
+ }
- return; /* queue froozen */
++ return; /* queue frozen */
}
/*
+ * if someone is waiting for the command to be active, wake it up
@@ -1422,17 +1438,17 @@
switch (why) {
case PWR_SOFTSUSPEND:
--=20
- Lubomir Sedlacik <salo@{NetBSD,Xtrmntr,silcnet}.org> --
--9wW02hG+pBvRTRBg
Content-Type: application/pgp-signature
Content-Disposition: inline
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.2.6 (NetBSD)
iD8DBQFCiQJ+iwjDDlS8cmMRAmDGAJsE0QdHSv2OHhsGpUvb6ERSXKNqrwCfeigD
ZQdfpMG2x9Q4ggoTzlTJdvI=
=nERy
-----END PGP SIGNATURE-----
--9wW02hG+pBvRTRBg--
From: Manuel Bouyer <bouyer@netbsd.org>
To: gnats-bugs@netbsd.org
Cc:
Subject: PR/30194 CVS commit: src/sys/dev/ata
Date: Mon, 16 May 2005 21:43:33 +0000 (UTC)
Module Name: src
Committed By: bouyer
Date: Mon May 16 21:43:33 UTC 2005
Modified Files:
src/sys/dev/ata: ata.c atavar.h
Log Message:
Add a ata_queue_idle() function, which freeze a queue and tsleep() until the
controller is idle.
Change the powerhook function to call ata_queue_idle() on standby/suspend,
and ata_reset_channel() on resume (to wake up the disks and start from a
clean state).
Fix PR kern/30194 by Lubomir Sedlacik.
To generate a diff of this commit:
cvs rdiff -r1.67 -r1.68 src/sys/dev/ata/ata.c src/sys/dev/ata/atavar.h
Please note that diffs are not public domain; they are subject to the
copyright notices on the relevant files.
From: Manuel Bouyer <bouyer@antioche.eu.org>
To: Lubomir Sedlacik <salo@Xtrmntr.org>
Cc: gnats-bugs@netbsd.org
Subject: Re: kern/30194: unrecoverable wd(4) error after suspend/resume
Date: Mon, 16 May 2005 23:44:46 +0200
On Mon, May 16, 2005 at 10:28:46PM +0200, Lubomir Sedlacik wrote:
> hi,
>
> On Mon, May 16, 2005 at 08:02:05PM +0200, Manuel Bouyer wrote:
> > can you try the attached patch ? I've not been able to reproduce your
> > problem, but the atabus power hook needs to be smarter than it is
> > actually.
>
> whooa! this made a whole lot of a difference (after fixing your patch
> to compile :).
Ops, I sent you an older version of the patch, I fixed theses to
test on my laptop. Sorry for this.
> i am now able to suspend/resume without disk losing
> interrupts and hanging. thanks a lot!
OK, I commited this, and will request pullups to 3.0_BETA in the next few
days.
--
Manuel Bouyer <bouyer@antioche.eu.org>
NetBSD: 26 ans d'experience feront toujours la difference
--
Responsible-Changed-From-To: kern-bug-people->bouyer
Responsible-Changed-By: bouyer@netbsd.org
Responsible-Changed-When: Mon, 16 May 2005 21:45:56 +0000
Responsible-Changed-Why:
I commited a fix for this, will request a pullup to 3.0_BETA in the next
few days.
From: Jeff Rizzo <riz@netbsd.org>
To: gnats-bugs@netbsd.org
Cc:
Subject: PR/30194 CVS commit: [netbsd-3] src/sys/dev/ata
Date: Fri, 27 May 2005 23:10:52 +0000 (UTC)
Module Name: src
Committed By: riz
Date: Fri May 27 23:10:52 UTC 2005
Modified Files:
src/sys/dev/ata [netbsd-3]: ata.c atavar.h
Log Message:
Pull up revision 1.68 (requested by bouyer in ticket #328):
Add a ata_queue_idle() function, which freeze a queue and tsleep() until the
controller is idle.
Change the powerhook function to call ata_queue_idle() on standby/suspend,
and ata_reset_channel() on resume (to wake up the disks and start from a
clean state).
Fix PR kern/30194 by Lubomir Sedlacik.
To generate a diff of this commit:
cvs rdiff -r1.66 -r1.66.2.1 src/sys/dev/ata/ata.c
cvs rdiff -r1.67 -r1.67.2.1 src/sys/dev/ata/atavar.h
Please note that diffs are not public domain; they are subject to the
copyright notices on the relevant files.
State-Changed-From-To: open->closed
State-Changed-By: bouyer@netbsd.org
State-Changed-When: Wed, 05 Jul 2006 17:07:22 +0000
State-Changed-Why:
Fix has been commited and pulled up a long time ago.
>Unformatted:
(Contact us)
$NetBSD: query-full-pr,v 1.51 2026/08/10 02:28:17 riastradh Exp $
$NetBSD: gnats_config.sh,v 1.10 2026/05/13 22:00:09 riastradh Exp $
Copyright © 1994-2026
The NetBSD Foundation, Inc. ALL RIGHTS RESERVED.