NetBSD Problem Report #460

From gnats  Mon Sep  5 13:12:18 1994
Received: from python.CS.ORST.EDU (root@python.CS.ORST.EDU [128.193.164.60]) by sun-lamp.cs.berkeley.edu (8.6.9/8.6.9) with ESMTP id NAA01552 for <gnats-bugs@sun-lamp.cs.berkeley.edu>; Mon, 5 Sep 1994 13:12:16 -0700
Message-Id: <199409051914.MAA22727@santiam.CS.ORST.EDU>
Date: Mon, 5 Sep 1994 12:14:10 -0700
From: "Jason R. Thorpe" <thorpej@mail.CS.ORST.EDU>
Reply-To: thorpej@mail.CS.ORST.EDU
To: gnats-bugs@sun-lamp.cs.berkeley.edu
Subject: scsi slaves treated as unit's
X-Send-Pr-Version: 3.2

>Number:         460
>Category:       port-hp300
>Synopsis:       scsi slaves treated as unit's
>Confidential:   no
>Severity:       critical
>Priority:       high
>Responsible:    gnats-admin (GNATS administrator)
>State:          closed
>Class:          sw-bug
>Submitter-Id:   net
>Arrival-Date:   Mon Sep 05 13:20:19 +0000 1994
>Closed-Date:    Mon Sep 19 00:27:46 +0000 1994
>Last-Modified:  
>Originator:     Jason R. Thorpe
>Release:        NetBSD 1.0_BETA (sup'd 9/4/94)
>Organization:
	Department of Computer Science
	Oregon State University
>Environment:
System: NetBSD santiam 1.0_BETA NetBSD 1.0_BETA (SANTIAM) #0: Thu Aug 11 13:42:08 PDT 1994 thorpej@santiam:/tmp_mnt/hurricane/NetBSD/src/sys/arch/hp300/compile/SANTIAM hp300


>Description:
	When attempting to place root and swap on a device other than
	slave 0, autoconf.c generates a warning:

		WARNING: using device at unit 0 of controller

	This is due to scsi being fundamentally different
	from hpib.  hpib drives have 1 controller per disk, whereas
	many drives hang off of a scsi controller.  These drives
	hanging off of the controller are being incorrectly treated
	as units, similar to the hp7946 (which has a disk at unit 0
	and a tape at unit 1).  The code always assumes unit 0, which
	in the case of scsi, is not necessarily correct.
>How-To-Repeat:
	bits from my kernel config:

	config netbsd root on sd0 swap on sd0b

	master          scsi0   at scode?
	master          scsi1   at scode?
	master          scsi2   at scode?
	master          scsi3   at scode?
	disk            sd0     at scsi0 slave 5
	disk            sd1     at scsi0 slave 6
	disk            sd2     at scsi0 slave 2
	disk            sd3     at scsi0 slave 3
	disk            sd4     at scsi0 slave 4
	disk            sd5     at scsi0 slave 5
	disk            sd6     at scsi0 slave 6
	disk            sd7     at scsi1 slave 0
	disk            sd8     at scsi1 slave 1
	disk            sd9     at scsi1 slave 2
	disk		sd10	at scsi0 slave 0
	tape            st0     at scsi? slave ?
	tape            st1     at scsi? slave ?

Note that scsi0, slave 0 is a cdrom drive...

Upon booting a kernel configured in this manner, after the autoconf
sequence, the warning message is generated and the kernel reports:

	changing root device to sd10a

...and then panics with a zero-divide trap, because the drive is
empty.  This behavior is not exihibited if booting off of an hpib
disk, no matter which slave, since the disk is always at unit 0 (at
least it is on all of my hpib disks...)

Note - just umplugging the cdrom won't do it, since sd0 is still at
slave (and therefore unit) 5 of scsi0

>Fix:
	Well, I can describe how I'd do it...

	Determine whether or not the root/swap is being done
	on a scsi disk.  If so, then set the unit # check to
	the slave id, and also use that number whenever unit 0
	is assumed.  If the disk is not scsi, then perhaps just
	default to unit 0, as the code does now.  Essentially, the following
	(at line 1024 of autoconf.c) is incorrect:

	if (unit != 0)
		printf("WARNING: using device at unit 0 of controller\n");

	mindev = hd->hp_unit;

	Actual code is unknown to me at the moment...But after enough
	coffee, I'm sure I can come up with something...


	This was caused by some misguided changes that were made relative to
	the 4.4-Lite code.  I've fixed this and a few other bugs.  - mycroft

>Release-Note:
>Audit-Trail:
State-Changed-From-To: open->closed 
State-Changed-By: mycroft 
State-Changed-When: Sun Sep 18 17:27:46 PDT 1994 
State-Changed-Why:  
Fixed. 
>Unformatted:

NetBSD Home
NetBSD PR Database Search

(Contact us) $NetBSD: query-full-pr,v 1.51 2026/08/10 02:28:17 riastradh Exp $
$NetBSD: gnats_config.sh,v 1.10 2026/05/13 22:00:09 riastradh Exp $
Copyright © 1994-2026 The NetBSD Foundation, Inc. ALL RIGHTS RESERVED.