NetBSD Problem Report #648

From gnats  Sun Dec 18 05:50:34 1994
Received: from pain.lcs.mit.edu (pain.lcs.mit.edu [128.52.46.239]) by sun-lamp.cs.berkeley.edu (8.6.9/8.6.9) with ESMTP id FAA11314 for <gnats-bugs@sun-lamp.cs.berkeley.edu>; Sun, 18 Dec 1994 05:50:34 -0800
Message-Id: <199412180551.FAA00897@try.idiom.com>
Date: Sun, 18 Dec 1994 05:51:41 GMT
From: muir@try.idiom.com
Reply-To: muir@idiom.com
To: FreeBSD-gnats-submit@freebsd.org, gnats-bugs@NetBSD.ORG
Subject: Ethernet board probes with message "Erase pencil mark!"
X-Send-Pr-Version: 3.2

>Number:         648
>Category:       kern
>Synopsis:       "Erase pencil mark!" does not leave enough clues
>Confidential:   no
>Severity:       non-critical
>Priority:       low
>Responsible:    gnats-admin
>State:          closed
>Class:          sw-bug
>Submitter-Id:   net
>Arrival-Date:   Sun Dec 18 06:05:04 +0000 1994
>Closed-Date:    Wed Dec 28 18:48:08 +0000 1994
>Last-Modified:  Wed Jan 06 10:28:59 +0000 1999
>Originator:     
>Release:        FreeBSD 2.0-RELEASE i386 *and* NetBSD 1.0 i386
>Organization:
Idiom Consulting
>Environment:



>Description:

	1 3C5x9 board(s) on ISA found at 0x300
	ep0: 3c5x9 at 0x300 in test mode. Erase pencil mark!
	ep0: eeprom failed to come ready.

	What does it mean?  Help!  

	The semantic content I get out of "Erase pencil mark" is:
	USE THE SOURCE, LUKE.   I will, but it would be nice if the
	probe failed with message that gave even the smallest 
	clue what was wrong.

	(Anyone have any clues they want to pass along?)

>How-To-Repeat:

	Aquire and assemble the following hardware:

		Motherboard     Intel Premier/PCI II 
		CPU             Intel Pentium 90
		32MB RAM
		PCI SCSI        ?? NCR53c810
		DISK            SEGATE ST32550N (2GB low power barracuda)
		ETHERNET        3COM Etherlink III 3c509B-TP
		VIDEO           ATI Ultra Pro 

	Try to install NetBSD 1.0 or FreeBSD 2.0.   

	The probe message above comes from FreeBSD 2.0, but NetBSD 1.0,
	produced almost identical messages.

>Fix:


>Release-Note:
>Audit-Trail:

From: Adam Glass <glass>
To: muir@idiom.com
Subject: Re: pending/648: "Erase pencil mark!" does not leave enough clues
Date: Sun, 18 Dec 1994 15:14:57 -0800



 The error message is a little unusual but correct.  Basically there is
 a test mode on the etherlink III boards.  If you make a pencil mark
 between two particular contacts over a provided surface, it goes into
 test mode.

 So what should the printf say?  the above "feature" isn't mentioned in
 the user manual.

 I suppose it could just say '...in test mode' and stop there.

 later,
 Adam Glass


	Actually, newer boards will also generate that diagnostic if they
	are in the `Plug'n'Play compatibility' mode.  The message has been
	changed to offer more advice, pending implementation of the
	Plug'n'Play stuff.  - mycroft

State-Changed-From-To: open->closed 
State-Changed-By: mycroft 
State-Changed-When: Wed Dec 28 10:48:08 PST 1994 
State-Changed-Why:  
Message has been changed to be slightly more informative. 
>Unformatted:

NetBSD Home
NetBSD PR Database Search

(Contact us) $NetBSD: query-full-pr,v 1.51 2026/08/10 02:28:17 riastradh Exp $
$NetBSD: gnats_config.sh,v 1.10 2026/05/13 22:00:09 riastradh Exp $
Copyright © 1994-2026 The NetBSD Foundation, Inc. ALL RIGHTS RESERVED.